710-409-00 Rev A, S48592-100R | IMS EP QC Checklist

Enter Serial Number *

Enter Job Number *

Customer (AUTO)

Part Number (AUTO)

Description (AUTO)

Page 1 - Final Inspection Checklist Sample Criteria

(Examples)

1. All edges are to be free from sharp and rough surfaces. *

Yes
No
N/A

2. Good powder paint coverage (No hanger marks, drips, or runs). Poor paint coverage not acceptable. *

Yes
No
N/A

3. No chipping, rust, or scratches. *

Yes
No
N/A

4. All welds must be ground clean and / or hidden. *

Yes
No
N/A

5. All PEM nuts are to be free of overspray, powder paint, and burrs. Paint on threads is not acceptable. *

Yes
No
N/A

6. Verify that male and female hinges are compatible. *

Yes
No
N/A

7. All metal parts shall be poly-bagged to prevent paint chipping and damage. *

Yes
No
N/A

8. Check all colors with provided samples. *

Yes
No
N/A

9. Verify shipping container shows no signs of leakage, such as holes or wet spots. *

Yes
No
N/A

Page 2 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm height, width, and depth is as referenced at 58.813 REF, 21.313” REF, .875 REF respectively.

Height *

Width *

Depth *

2. Confirm Door Handles, Latching Mechanism and Hinges function without obstruction. *

Yes
No
N/A

3. Confirm paint all surfaces, except where indicated( Flag#6) , are texture light gray.***No overspray is permissible*** Must compare against archived color sample. *

Pass
Fail

4. Confirm masked edge of circle all around .07”. Flag #5 *

Yes
No
N/A

5. Confirm Ground stud location. Flag #7 ; Add pc part marking after finishing, on the surface indicated Flag#4 *

Yes
No
N/A

6. Confirm the far side of the unit at the location indicated is marked per Teradyne Inc. Control Document #CD0002 Method #6 (Black Ink 1/8”-1/4” height in san serif gothic font – “Teradyne Part Number”, ”Revision Letter” “Vendor Code”, ”Date Fabricated”. Date Fabricated to be XXYY where xx=week and yy=year.) Example: 987-684-00A 100330 2911 *

Yes
No
N/A

Page 3 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm the presence of Loctite 242 on hardware at Cam Latch location (2 Places). *

Yes
No
N/A

Page 4 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm there are 9 snap in nylon buttons at the location indicated. *

Yes
No
N/A

Page 5 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm the presence of Loctite 242 on the Southco Lock Assembly. *

Yes
No
N/A

2. Confirm the stack up of the lock assembly is as follows: Lock Assembly, Washer, and Hex Screw. *

Yes
No
N/A

3. Confirm the Lock Assembly is Torqued to 38-45 in-lbs using a Torque Wrench. *

Yes
No
N/A

Page 6 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm the orientation of the Lock Assembly when viewed from the front of the door is as indicated with the small dimple on the front facing downward. *

Yes
No
N/A

Page 7 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm the Locking Bar is situated between the door Brackets as shown and that the Open section of the Locking Bar is not deformed and is situated at the bottom of the door nearest the perforated section. *

Yes
No
N/A

Page 8 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm the orientation of the handle in the “home” position is parallel to the left / right side of the door and measures 4.20” +/-.050” from the outside of the door to the top of the handle and the outside of the door to the bottom of the handle as shown. *

Yes
No
N/A

Top Measurement *

Bottom Measurement *

Page 9 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm door latches contain the appropriate hardware. *

Yes
No
N/A

2. Confirm door hardware is not compressed or deformed. *

Yes
No
N/A

3. Confirm the texture from the handle plate and handle are of the same finish. *

Yes
No
N/A

4. Confirm there are no defects in the handle as defined in Teradyne QAA-065-001. Inspector must print and review during inspection. *

Yes
No
N/A

Page 10 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm the CAM hardware is torqued to 75-80 in-lbs using a Torque Wrench. *

Yes
No
N/A

2. Confirm the presence of Loctite 242 on the threads of the CAM assembly. *

Yes
No
N/A

3. Confirm the stack-up of hardware is as follows: Lock Washer, Hex Nut. *

Yes
No
N/A

Page 11 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Visual Inspection – Confirm metal finish color is yellow plating. No corrosion or scratches through coating are allowed. *

Yes
No
N/A

2. Functional Test – Confirm doors close tight creating a seal between door and the frame. *

Yes
No
N/A

3. Functional Test – Confirm doors latch in the closed position and are able to turn to the closed position. *

Yes
No
N/A

4. Functional Test – Confirm the locking bar stays in current position and is not “free falling”. *

Yes
No
N/A

5. Functional Test – Confirm door latches move freely without difficulty. *

Yes
No
N/A

Page 12 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm the function of the Lock Cam. There should be no obstruction or interference.. *

Yes
No
N/A

Page 13 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm the hardware for each screw on the hinge is tightened to 17-20 inch-lbs. 8 locations. *

Yes
No
N/A

2. Confirm the presence of 8 plastic washers between the door and the door hinge. *

Yes
No
N/A

3. Verify the hinge position is as indicated after hinges are tightened. *

Yes
No
N/A

4. Verify that male and female hinges are compatible. *

Yes
No
N/A

Page 14 - Final Check Criteria

Examples found on Page 1 / Use arrows when applicable.

1. Confirm the door is marked per Teradyne drawing specifications. (Part Number – Rev Letter – Supplier Code – Date Code) (Example: 977-233-00 E 100300 0213) Date Code is Week/Year. *

Yes
No
N/A

2. Confirm the location of part # stamp marking, refer to job traveler notes and print for part # stamp details and location. *

Yes
No
N/A

Take the following photos:

Inside the cabinet – Front *

Click or drag a file to this area to upload.

Inside the cabinet – Rear *

Click or drag a file to this area to upload.

Side of cabinet, no panels – Left *

Click or drag a file to this area to upload.

Side of cabinet, no panels – Right *

Click or drag a file to this area to upload.

Silk screen – Front *

Click or drag a file to this area to upload.

Silk screen – Rear *

Click or drag a file to this area to upload.

Finished unit with doors and panels assembled – Front, Back, Right side, Left side *

Click or drag a file to this area to upload.

Serial Number *

Click or drag a file to this area to upload.

Packed unit *

Click or drag a file to this area to upload.

Comments

I acknowledge that the above information is complete and accurate (sign name) *

Clear Signature